Delair Support
-
delair.ai
-
Get Started
- What is delair.ai ?
- Supported Drones & Devices
- Create a New Project
- How to create a new Mines & Aggregates Project
- How to create an Agriculture & Forestry Project
- How to upload 5 bands aerial images for Agriculture & Forestry project
- Launch of Photogrammetry for Agriculture & Forestry
- Creating a New LiDAR Project
- Coordinate Reference Systems
- Ground Control Points
- Data Processing Workflow
- Adding New Data to an Existing Project
- CAD Files Support
- General Information
- Administration
-
Flight Data Acquisition
- How to upload Aerial images as an Operator
- Drone flight parameters for Agriculture
- Drone flight parameters for Forestry
- Drone flight parameters for Mines & Aggregates
- Drone flight parameters for Corridors
- Drone flight parameters for Power Line inspection
- Drone flight parameters for Solar Panel inspection
- General Drone Flight Parameters (all industries)
- Data Processing
- Data Viewing & Editing
- Analytics
- Data Sharing & Exporting
- Software Development Kit
- Field Inspections
- BIM with delair.ai
- Integrations
- Security & Maintenance
- Terms & Conditions
- Release Notes
-
Get Started
-
Delair UX11
-
Delair UX11 video tutorials
- UX11 Content
- UX11 Unboxing & packing
- UX11 Assembly
- UX11 Disassembly
- UX11 Battery charge
- UX11 Delair Flight Deck Installation
- UX11 Association
- UX11 Mission planning
- UX11 Control surfaces test
- UX11 Take-off
- UX11 Abort Landing
- UX11 Flight Termination System
- UX11 Data transfer
- UX11 Delair Flight Deck Update
- UX11 Firmware update
- UX11 Delair Link update
-
Delair UX11 FAQ
- FAQ 001 - Where I can find the UX11 User Manual?
- FAQ 002 - How the wings are fixed to the body?
- FAQ 003 - How do I associate my UAV in maintenance procedure?
- FAQ 004 - How do I check APN configuration on the Tablet for the 3G/4G connection?
- FAQ 005 - How the offset for landing zone can be set?
- FAQ 006 - Why do I have a failed ground sensor test?
- FAQ 007 - Why do I don't have the "Firmware Update" button?
- FAQ 008 - How do I retrieve the flight log files when requested by Delair Support?
- FAQ 009 - What should I do if I have a communication loss ?
- FAQ 010 - How do I launch the UX11 for take off?
- FAQ 011 - How do I process my UX11 data in Delair After Flight?
- FAQ 012 - What are the available exported files after processing a dataset in Delair After Flight
- FAQ 013 - What are the UX11-3B camera specifications?
- FAQ 014 - What are the Delair After Flight system requirements?
- FAQ-015 What's the best UX11 Workflow with TBC UASmaster and Pix4D
- FAQ-016 How do I format the UX11 SSD and in which format
- FAQ 018 - Software downloads & updates
- Latest Release
- User Documents
-
Delair UX11 video tutorials
-
UX5 and DT18
- Latest release of UX5 and DT18 resources
- Support Bulletin
- UX5 Series
- UX5 FAQ
-
UX5 Series FAQ
- FAQ-0001 How to update the Aerial Imaging software?
- FAQ-0002 How to extract the GWT file?
- FAQ-0003 Why does AeriaI Imaging not detect the GNSS hardware?
- FAQ-0005 Why don't I have a GPS signal?
- FAQ-0006 The error 235 appeared during a flight, what are the consequences?
- FAQ-0010 My UAV starts descending after reaching the desired altitude
- FAQ-0013 Why is the battery percentage suddenly dropping?
- FAQ-0016 Why is my aircraft flying up and down?
- FAQ-0022 Why is my communication range so short?
- FAQ-0023 Why do I have "No GNSS hardware detected" error message on my tablet
- UX5 HP FAQ
- UX5 Series User Documents
- UX5 AG FAQ
- FAQ DT18
- DT18 Maintenance guide
- MyDelair